Assistance Produit

Support PrepGo Formula Feed Maker Set

Getting Started

What’s in the box?

400ml hot flask 

240ml cool flask 

2x Natural Start 150ml Bottles 

2x formula powder dispensers 

1x cleaning brush

How to make a feed

Before use: 

• Clean and disinfect the surface you are going to use. It is important that you wash your hands. 

• Fill the kettle with fresh tap water (do not use water that has been boiled before). Boil the  

water.  

Take care when handling freshly boiled water.

Hot flask 

Fill the hot flask with boiling water to take out and about with you. Water will remain hot for up to 4 hours if filled to the max level excluding the neck. 

Cooling flask 

  1. Press and hold the power symbol for 3 seconds to turn the lid on/off. Once the lid is switched on, a green star will appear. If inactive, the green star will disappear after 3 seconds, but the lid is still switched on. The lid will automatically turn off after 40 minutes to reserve battery power.  

  1. Measure out the formula as per manufacturer instructions and store in the milk powder dispenser until it’s ready to use. 

  1. Add boiled water to the cooling flask, using the graduation marks on the inside of the flask as a guide. Note: you can also measure out the boiled water in a bottle before decanting into the flask. 

  1. Screw on the digital lid tightly and turn the cooling flask upside down for a minimum of 5 seconds. Tap the power symbol to display the star on the digital lid, it should turn red. 

  1. Decant the formula powder from the milk powder dispenser into the cooling flask. 

  1. Ensure the lid is screwed on correctly and shake well to mix the powder with the hot water, ensuring it’s fully dissolved. Shaking the cooling flask starts the cooling process. 

  1. The time it takes for the feed to cool depends on the feed size, refer to the cooling times table for more information. To check if a feed is ready to dispense into a baby bottle, turn the cooling flask upside down for a minimum of 5 seconds so the milk touches the digital lid. Tap the power symbol to display the star, the lid will show a green star when the feed is ready. Don’t dispense the feed before minimum cooling time. 

  1. Decant your feed into a clean, sterile bottle, and follow bottle feeding instructions. Always check the temperature before feeding your baby on the inside of your wrist - it should feel lukewarm, not too hot or cold. Once a feed is made, use immediately. 

The digital lid

The integrated thermometer in the digital lid will activate the digital screen when it comes into contact with water or milk. On the cool flask, the digital lid will tell you when a feed is ready for baby (green star) or when it’s too hot (red star). 

To help maintain battery life switch the digital lid off between feeds by pressing the power symbol for 3 seconds. 

Cooling and reset time

Cooling times should be used as a guide only. Always check food temperatures before feeding. Always follow formula powder manufacturer’s instructions for making a feed.

The cooling flask works by absorbing heat from hot liquids. After being exposed to heat, it will require 3-4 hours minimum before being ready to use again. To help accelerate the reset time you can add cold water to the unit and place in the fridge. 

 

Cleaning and sterilising

How to Clean

Hot flask  

The hot flask base and lid can be cleaned in warm soapy water or a dishwasher. 

Cooling flask

The cooling flask base can be cleaned in warm soapy water or a dishwasher. 

The digital lid can only be washed in warm soapy water. Make sure to remove the silicone seal and clean behind using the small brush provided. Follow the instructions below to sterilise the cooling flask with the digital lid.

Sterilisation methods

Descaling (base only)

To avoid the build-up of limescale the container should be periodically cleaned. The best results are obtained using a mixture of water and bicarbonate of soda or washing up liquid. Rinse thoroughly afterwards. 

 

DOs and DON’Ts

DO: 

  • Press the power symbol for 3 seconds to turn on the digital lid. The digital lid will automatically turn off after 40 minutes to preserve battery power. 

  • Turn the cooling flask upside down and tap the power symbol to check the temperature. Remember the star will go green when the feed is ready. 

  • Wait 3-4 hours, depending on cleaning and sterilising method, for the cooling flask to reset. 

  • Inspect the lid before using and ensure silicone seal is fitted. 

DON’T: 

  • Dispense the feed if the digital lid shows a red star. 

  • Dispense before minimum cooling time (see table for minimum cooling times). 

  • Store a made-up feed in the flask. 

  • Panic if you hear a crackling sound when making your feed. This is the cooling flask in action. 

  • Use if the star is flashing red.