Assistance Produit

Merci d'avoir acheté le préparateur de biberons portable PrepGo Tommee Tippee. Cette page d'assistance produit est destinée à vous aider à apprendre à utiliser et à entretenir votre préparateur de biberons, et à répondre à toutes vos questions.

Manuel produit

Support Page PrepGo Formula Feed Maker

Using your product

How to use

  1. Clean and disinfect the surface you are going to use. It is important that you wash your hands.
  2. Fill the kettle with fresh tap water (do not use water that has been boiled before). Boil the water.
  3. Take care when handling freshly boiled water.

Using the hot flask and cooling flask 

  1. Press and hold the power symbol for 3 seconds to turn the lid on/off. The lid will automatically turn off after 12 hours to reserve battery power.
  2. Add boiling water to the cooling flask, using the graduation marks on the inside of the flask as a guide.
  3. Measure out the formula as per manufacturer instructions and store in the milk powder dispenser until you are ready to use.
  4. You can now pour the water from the hot flask into the cooling flask using the graduation marks on the inside of the flask for correct measurements
  5. Add the correct amount of formula powder, as per manufacturers guidelines, in line with the amount of water in the flask.
  6. Screw the digital lid onto the cooling flask, ensuring it is assembled correctly, and shake well to mix the powder with the hot water, ensuring it's fully dissolved. Shaking the cooling flask starts the cooling process.
  7. The time it takes for the feed to cool depends on the feed size, refer to the table below. To check if a feed is ready to dispense into a baby bottle, tilt the cooling flask sideways for a minimum of 5 seconds so the milk touches the digital lid. The lid will show a blue star when the feed is ready. Don’t dispense the feed before 2 minutes
  8. Decant your feed into a clean, sterile bottle. And follow bottle feeding instructions.
  9. Always check the temperature before feeding your baby. Once a feed is made, use straight away.

Using the cooling flask 

    1. Press and hold the power symbol for 3 seconds to turn the lid on/off. The lid will automatically turn off after 12 hours to reserve battery power.
    2. Add the boiled water to the cooling flask, using the graduation marks on the inside of the flask.
    3. Add the correct amount of formula powder, as per manufacturers guidelines, in line with the amount of water in the flask.
    4. Screw the digital lid onto the cooling flask, ensuring it is assembled correctly, and shake well to mix the powder with the hot water, ensuring its fully dissolved. Shaking the cooling flask starts the cooling process.
    5. The time it takes for the feed to cool depends on the feed size, refer to the table below. To check if a feed is ready to dispense into a baby bottle, tilt the cooling flask sideways for a minimum of 5 seconds so the milk touches the digital lid. The lid will show a blue star when the feed is ready. Don’t dispense the feed before 2 minutes
    6. Decant your feed into a clean, sterile bottle. And follow bottle feeding instructions.
    7. Always check the temperature before feeding your baby. Once a feed is made, use straight away.

    The digital lid

    The integrated thermometer in the digital lid will activate the digital screen when it comes into contact with water or milk. The digital lid will tell you when a feed is ready for baby (blue star), but also when water is still hot enough to start making a feed (red or orange star). To help maintain battery life switch the digital lid  off between feeds by pressing the power symbol for 3 seconds

    When testing the temperature of milk (on the cooling flask)

    Under most circumstances the digital lid will not show a red star when attached to the cooling flask. This is because the cooling flask will start cooling the feed immediately and brings the feed temperature below the range that would show a red star.

    Cooling times 

    Cooling times should be used as a guide only. Always check food temperatures before feeding. Always follow formula powder manufacturer’s instructions for making a feed.

    The cooling flask works by absorbing heat from hot liquids. After being exposed to heat, it will require a minimum of 3 hours before being ready to use again.

    The cooling flask works by absorbing heat from hot liquids. After being exposed to heat, it will require a minimum of 3 hours before being ready to use again.

    Sterilisation & Cleaning

    Guidance on how to clean and maintain your GoPrep

    The flask can be cleaned in warm soapy water or a dishwasher, and it can also be sterilised (see table below). The lid can be washed in warm soapy water - take care to remove the silicone seal and use the small brush provided to clean behind the seal of any excess milk. The flask and lid should be cleaned and sterilised after every use.

    Descaling (flask only)

    To avoid the build-up of limescale the container should be periodically cleaned. The best results are obtained using a mixture of water and bicarbonate of soda or washing up liquid. Rinse thoroughly afterwards.

    Do's & dont's

     

    FAQ d’assistance

    Le couvercle numérique doit être nettoyé à l'eau tiède savonneuse, à l'aide de la petite brosse fournie si nécessaire, et il peut être ensuite stérilisé dans un stérilisateur ou à l'eau froide.

    Une pile longue durée est scellée dans le couvercle. Elle est conçue pour durer pendant tout le parcours d'alimentation au biberon. La durée de vie exacte de la batterie dépend de l'usage.

    L'élément refroidisseur du thermos a besoin d'une durée de 3 heures pour retourner à son état initial après utilisation. Lorsque vous appliquez de la chaleur au niveau du thermos, la phase de refroidissement de 3 heures commence une fois que vous le laissez reposer. Par conséquent, si vous avez lavé le thermos à l'eau chaude, puis stérilisé, le temps de refroidissement commence après l'étape de nettoyage et de stérilisation.

    Nous ne conseillons pas de préparer un biberon en vue de le stocker, conformément aux recommandations en la matière. Un biberon doit être préparé en vue d'une utilisation immédiate, et tout reste de lait infantile dans le biberon doit être jeté. Le stockage pendant un certain temps n'est pas recommandé.

    Le thermos contient jusqu'à 240 ml d'eau (8 oz), par conséquent vous pouvez préparer des biberons à hauteur de cette contenance, soit un seul biberon ou plusieurs petits.

    L'eau bouillante reste chaude dans la bouteille (pour préparer un biberon) pendant 4 heures minimum, selon la quantité d'eau contenue.

    Des graduations sont présentes à l'intérieur du thermos refroidisseur pour aider à mesurer les quantités. Vous pouvez également mesurer la quantité nécessaire dans un biberon puis la transférer dans le thermos refroidisseur

    La durée de refroidissement dépend de la température de l'eau dans le thermos isotherme et de la taille de biberon requise. Veuillez vous reporter aux instructions pour obtenir des recommandations sur les durées de refroidissement.

    Need extra support? you’re not alone

    We're here to help… You can contact us via live chat. Look for the icon to ask a question or chat to one of our friendly support team.

    Contact Us